V
LX: O que faz sentido se a medição da rede do sistema estiver configurada para o inversor/carregador. Why not? the inverter is disconected from from, the evcs is able to do stand alone, everything is present to do some magic! LX: Com cargas antes do inversor, espera-se que haja um medidor. (Você diz que resolveu isso com o Node-RED, mas também não disse de onde vêm os dados para esse medidor virtual.) A segunda expectativa com a redução de picos é que a bateria forneça energia às cargas, seja…
V
Merci. Maintenant, je vois bien ce que tu as fait. Ça fait au moins 15 ans que je ne joue plus avec ça.
V
Vince38: le chassis des batteries est à la terre comme prévu. Oui & Non. Tout dépend comment tu déclares ton installation, IT ou TBTS. S’il y a raccordement, c’est IT et il faut un CPI. S’il n’y a pas de raccordement, c’est la TBTS et il ne faut pas de CPI. LX: Checking for DC ripple. Envisageable. Les câbles Pylontech ne font que 21mm² (4AWG) et non 25mm². Il manque du cuivre pour bien faire. Est-ce que tu recommanderais de mettre 2 paires par batteries, soit 6 au total ? Dans la compatibilité…
V
As of v3.90-beta14 it lists Shelly RGBCCT working, does that mean the Shelly RGBCCT lightbulb or the Shelly Pro RGBWW PM LED controller? I thought the patchnote meant the LED controller but as of the Beta version, my controller is still not working. greetings,
V
Auch wenn ich die Widgets öffne, während der Tank noch aktiviert ist, steht hier leider kein “Delete”. Hast du noch eine Idee?
V
EVCS E-01 no GND pressent Is it really so difficult for you to tell me what Victron is doing wrong and send a photo? The assumption that I have a photo is a problem. And then as a return is it so difficult for you to scan up the thread to the already posted photo of the open devices? And the second assumption that Victron has done something wrong. If there is a ground fault error surely that is the place to start -the wiring? EVCS E-01 no GND pressent Deutschsprachiger Bereich Messe auch im…
V
Angeschlossen ist nach Anleitung. Plus aus der Vorbereitung von LM/Batterie zum Ladebooster und von da an die Batterie. Einstellung war erst auf Automatik und dann hab ich rumgespielt 4. Bedienung, Konfiguration und Überwachung Leider steht der Van gerade im Lager und ich kann aktuell nicht gucken.
V
This seems very similar to my issue as it only occurs when the Wakespeed is disconnected (when the ignition is turned off) I have run across a solution on my end that has worked. I Backdated the Firmware for the Cerbo GX to 3.79V and have not had the VEcan instance code return, When i look at the VEcan error log codes its still logging error codes (because communication is still being lost when the ignition gets turned off) but they are not setting a code. My best guess is the updates 3.80V and…
V
Die Zuleitung ist nur 6m Lang und in 5x10mm² ausgeführt, Die DC Kabel sind 70mm² und 80cm lang, da sollte es keine Probleme geben denke ich. Die Firmware ist auf allen 570. Ich Habe jetzt den Anschluss von Phase 1 und 3 Getauscht und neu konfiguriert. Bis jetzt läufts, mal schauen wie lange.
V
Hallo allemaal, wanneer ik 3.9 beta 14 installeer zie ik in vrm bij de instellingen geen dess instellingen meer. ook de grafieken hiervan verdwijnen inclusief de accu voorspellingen. iemand een idee? in versie 3.85 zit deze instelling er wel. Ook het in en uitschakelen van trade of green is dus verdwenen.
V
Hi all, I’m looking for a way to set ‘0-on-the-meter’ for Multi RS Solar set-ups with DC coupled PV. The setting in the screenshot works very well to achieve this, but I don’t find a way to set this parameter in nodered. There’s a lot of options in AC system control, system settings custom control and even Dynamic ESS nodes that refer to the feed-in, but none seem to have any effect. Perhaps anyone has a tip If not, perhaps someone from the Victron team can take it along as a feature request.
V
Monte mi primera instalacion victron en el 2006. Hace 20 años, y he ido mejorandola poco a poco al igual de la casa de un amigo y tres autocaravanas… Tan complicado es que me digan que el lo que Victron esta montando mal y mandar una foto? Y lo de copiar/pegar de la IA eso es lo que harás tu. Otros tenemos conocimientos más avanzados
V
14.2v, and the Li-ion battery setting, is appropriate for Victron LFP batteries; for 3rd-party batteries, you will likely need to set the charge profile in accordance with the battery manufacturer recommendations (see the battery’s user and installation manual for details). The current dropping and mode switching may indicate that either the battery is already more fully charged than it thinks it is (common occurrence with built-in SOC estimations) or it’s highly imbalanced and the BMS is…
V
Salve a tutti, ho collegato il Blue Smart IP22 Charger 12/30 Output 230V alla nuova batteria al litio della LiTime da 320Ah. ho settato il tipo batteria come Li-ion, ma vedo che dal IP22 carica la batteria alla tensione di 14,20V. con appena 5,9A. in funzione di Assorbimento. poi passa in funzione Stoccaggio quando ancora la batteria è al 61 % di carica e l’IP22 cessa di erogare corrente. Qualcuno può darmi qualche spiegazione ? Grazie a tutti.
V
Hallo, Victron beschreibt ein sehr selten aufkommendes Problem mit LOM und Overload….. vielleicht… victronenergy.com VEConfigure: grid codes & loss of mains detection [Victron Energy]
V
Du musst die Seite (wie der Screenshot von Dir zeigt) aufrufen, BEVOR Du den Tank wieder deaktivierst via Console. Dann klickst Du (siehe Screenshot von Dir) auf “Delete” und dann sollte der “Tank [20]” verschwinden…
V
Schon sehr seltsam so ganz ohne reale Belastung … Um das Ganze einzugrenzen müsste man jetzt einfach die Phasenzuordnung ändern und die geänderte Config nochmals draufschieben … da du ja alle Lasten vor den Multis hast, wäre das ja kein Weltuntergang. Ein Problem zwischen den Multis auf Grund des Hardwarestandes schließe ich mal aus … das waren ja nur ein paar Monate dazwischen … FW ist bei allen gleich ?
V
You are right. If that doesn’t work, then a physical swap may still be need to rule out wiring/switch gear/installation as the cause
V
Its not. Its poor mans connectivity without reliable failover. If the cerbo has connection over wifi, why does it prioritize ethernet where it can’t get through? I understand the current design but I disagree with it. What I’ve discovered Initially, I suspected a problem with the Cerbo GX or its Ethernet interface. However, I’ve now reproduced the underlying network behavior using a Mac connected directly to the Nighthawk M5 via Ethernet, without the Cerbo involved. With the Nighthawk switched…
V
Currently that is not possible. The units share a desired charge equally, and if one unit hits a per-phase current-limit, then that unit will reduce the charge power to obey the current limit configured. Also DESS does not control individual units, but threats them as one inverter.
V
Kirchhoff’s law requires it. The sum of currents at any node must be zero.
V
That is a bad idea, you should only have the grid meter connected and visible to the system, while the system is grid connected. If it isn’t, drop the meters connection. Else, several things may use readings from the grid meter, which do not fit into the real systems layout.
V
Because I have the grid as a backup (with a Victron energy meter configured as a grid meter), but the grid is not connected to the MultiPlus
V
You could make something with nodered to control the open dtu , but I wouldn’t mind a real dynamic throttling all too much: Connect your hoymils behind a shelly device, and when your system reaches 98 or 99% where feedin will happen soon, shut off the shelly. When soc drops bellow 97%, turn it on again, the hoymiles will then resync and ramp up again. (That would also allow you to use the shelly-pvinverter-integration to have the hoymils visible in the system / vrm as ac coupled pvinverter)
V
ESSGobel: kann ich das automatisieren (Node Red), wenn die Batterie einen Zelle am unteren Limit erkennt, dass der Shunt auf 0% geht? Der Shunt resetet sich auf 100%, wenn nach Volladung der entsprechende Tail-Current erreicht wird. Wenn du beim Erreichen der Low-Voltage Grenze “0%” da stehen haben willst, dann musst du im Shunt die Battery-Size kleiner konfigurieren als sie wirklich ist. Aber wirklich sinnvoll ist das nicht, du müsstest dann auch einen minsoc 0 erlauben, und das beißt sich…
V
Why is there a grid on ac input 1 in a off-grid system? If some meter is accidently configured as “Grid” that may cause all sort of strange calculations.
V
Diessel: 7-day CHR/DSC cycles between 20% and 80%, without reaching SOC 100%. I’ll have this during winter for sure, probably even longer. Will post an update after a while to see how it works out I’ve now configured my dynamic cutoff to 3.06V per cell (46V) and will be curious, what the shunt concludes, when this is hit. Then, might go a bit lower if needed (3 / 45). Usally one says 2.8 is fine, but from 3 to 2.8 isn’t much energy anyway.
V
VictRon54: On a non-isolated unit, you don’t need such a thick earth cable; that cable is only for the Orion’s own earth, and very little current flows through it. Wrong for a unit with a large voltage reduction or boost as has been said above, this system is 12V to 24V so the negative cable takes the difference in current flows plus losses, up to 30A is expected. On a system with equal voltages it will be less than 10A.