V
Hatte die Antwort letzte Woche schon geschrieben, aber nicht abgeschickt Mike: Sind die 200-300W Eigenverbrauch der MP ein Erfahrungswert von dir? Ich hatte ins Datenblatt geschaut und da steht 28W Standbyverbrauch für einen 10000er MP. Die 200-300W sind meiner Erfahrung nach wesentlich realistischer als 90W (3x28W). Wir sagen unseren Kunden immer, das sie mit etwa 1% der Wechselrichterleistung als Eigenverbrauch rechnen sollten. Habe es eben noch mal mit einem 5000er MultiPlus-II und einem…
V
Hast Du die im RMA Formular vorgeschriebenen Tests durchgeführt? Die vorgestellten Einstellungen sehen normal aus (AES sowie Vergleichbares über Node Red ist nicht aktiviert, oder?). Melde einen Gewährleistungsfall an und halte uns hier auf dem Laufenden!
V
Dean Perry: Not sure if I can post mine - it’s a work project. If anyone wants to get that info from the Pylontechs, just need to look over the extended CAN commands that can be found in the Pylontech doc in the topic below. Venus OS 3.75 — can-bus-bms driver intermittently sets false Warnings etc Modifications Did you tried to use candump on the CAN port on which the battery is connected? To see the content of the CAN frames and their IDs? Then you can use these two specs below to get an image…
V
Look at the ‘EV Charger State’ graph from the ‘Advanced’ view of VRM, and also ‘EV Charger Power’. What is reported across your charging cycle: plug car in charge charging fails unplug car plug car in charging starts (… charging fails) Grab a screenshot of that timeline from the Advanced view of VRM
V
Changed to superuser to confirm, that the communication between mppt and multi is working in this regard. everything seems ok. went on site today and changed to 3 hours fixed absorption time. lets see, if that does the trick. I am still not sure about the voltage levels though. something seems off to me… will report back after a few cycles.
V
De installatie is recent gekeurd geweest en voldeed aan alle normen. Wat stelt u eventueel voor om verder na te kijken?
V
@M_Lange Sind die 200-300W Eigenverbrauch Erfahrungswerte? Das wäre mir wirklich zu viel. Laut Datenblatt sollten es nur 28W pro Gerät sein.
V
Take a look at this manual: victronenergy.com 6292-ESS_design_and_installation_manual-pdf-en.pdf 1228.45 KB
V
hast du nicht mal eine Typenbezeichnung oder einen Herstellerlink für uns … klingt ja erstmal NUR nach einem einfachen Notstart über Schließer … geschlossen = Motor springt an und läuft … geöffnet = Motor geht aus … reiner Verdacht aber das wäre die einfachste Lösung für die Einbindung eines Relaisassistenten.
V
Alles was du am AC Out1 hast wird automatisch weiter versorgt. Der AC Out2 schaltet im Normalfall bei fehlendem AC In weg. Die Wärmepumpe kann weiter versorgt werden, wenn sie 1phasig wäre und nicht zu viel Leistung benötigt. So viel kennen wir ja noch nicht von deinem System … aber bei zu wenig PV macht eine Wärmepumpe wieder keinen Sinn. 6 US5000 sind zwar nicht so schlecht aber eine WP läuft ja auch eine Weile … + die anderen wichtigen Lasten noch oben drauf.
V
Hi, I have a new cargo trailer with a 48V battery that runs the cargo lights and other small loads. Should I add a separate 12V battery for equipment that can’t run on 48V, or install an Orion DC-DC charger/converter? I’m concerned about efficiency loss with the Orion. Adding a 12V battery would also mean installing a separate solar charging circuit, though I have plenty of room on the trailer roof. I’m trying to keep costs down, but I also like the idea of having a backup 12V battery if…
V
Hi Martin, looks fantastic. You can access the extended data over CAN, using socketcan, without requiring a diagnostic cable. There are a couple of wrinkles: they have to be running a relatively modern Pylontech firmware version (say, later than 2022) so they have BMS protocol > 2.0, and they have to not be behind an LV-Hub. Here’s something way less pretty (+mashed formatting due to Chrome screen cap) that I’ve been working on: and from a system running a slightly later version of the script…
V
Jochen snauwaert: Voltage between N and earth: 8 V The CP signal on the charging cable is referenced to the earth. If the neutral or earth are bouncing around because of poor earth bonds or a flaky neutral connection somewhere, then the EVCS can act as if the vehicle is charged and just stop charging. The signalling is at 12/9/6 volts, so a little bit of common-mode noise can make a difference.
V
I see what you are trying to do here and it makes sense. I just don’t think this is a good idea. Starter batteries aren’t meant for larger sustained loads. They are not “deep cycle” in the sense that you will drastically reduce the lifespan of the battery by regularly deeply discharging it. Also, you definitely run the risk of stranding yourself. The most you would want to do is use an inverter for very small and intermittent loads. There may also be issues with the demand put on the alternator…
V
I got it figured out. You’re not going to believe it but it’s the Guest battery cut-off switch. The battery side of the switch is not being turned on or is blocking the vast majority of the power. The reason it was taking roughly 10A earlier was because the power was coming through the solar and that’s why it tapered off in the evening (the sun went down). That doesn’t go through the switch. I ran a bunch of temporary jumper wires to bypass the switch until I can take it apart tomorrow but that…
V
Manchmal muss Laden und Entladen freigegeben werden.
V
This is so weird. The app shows 50%, the shunt shows 50% and now it’s basically taking little to no amps. App shows 13.3v and Victron GUI shows 13.24v I decided to do a real-world test. If the SOC is 50% then it should power the loads for some time. I shut off the grid and everything instantly went dark and I got some emails stating low battery. Something’s wrong.
V
No the battery soc will invariably be garbage, especially first dew cycles when it hasn’t fully charged and reset. The shunt will provide the reference, true value, assuming its correctly configured. But if you havent fully charged yet, it doesn’tknow where 100% is.
V
How do i configure my system for grid failure backup? 2x Multis, 6x Pylontec US5000, Solar MPPT, heat pump, Venus GX.
V
Yeah, but the SOC is 50% according to the app. I manually adjusted the shunt to the same so it’s now in the same ballpark. If I turn off the Multiplus, and then turn it back on, it gives a low battery error and then eventually starts up. If the SOC is 50% (13.3v is what the app says) then shouldn’t it take more than 4A ? I would think the current would fall off as it nears the top of the charge. It should be hours from that with a 50% SOC. I turned the battery off and removed the negative cable…
V
have EVCS with firmware v2.09/5.2 connected to Cerbo GX, 3*Multiplus II 48/3000, 60kWh PV battery, 20kWp PV modules, BYD Dolphin Surf. EVCS configuration: mode = manual, current = 6A. location = acOut start charging at backup battery SoC: 90% stop charging at backup battery SoC if off grid: 85% Allow battery/grid power for auto mode: enabled Allow low excess solar power for auto mode: enabled it is midnight (no PW power), PV battery is at 83%. I click “start charging” and EVCS starts to draw…
V
As a battery approaches full charge it will start to accept less current, eventually tapering to 0. Its common for a new lfp battery to require several charge cycles to achieve full balance at the top end.
V
Odd…I have it installed and I set the solar chargers to the Lithium preset. I have the charging amps set to 60 and then tried 120 (max) before going back to 60. The bluetooth app shows that the SOC is 49%, the shunt (which was set for lithium) shows 94%. But here’s the real issue, the battery is only taking around 8A and both the bluetooth and the Victron GUI show the same. Also, the interior lights (LED on DC) are pulsing from dim to normal in a cycle. The big question is, why is it not taking…
V
MIjn oplossing vandaag was om de cerbo te rebooten. Ook 3.85
V
I operate 3 of the 450/200 MPPTs. I string between 10 and 12 PV panels to each. They have been working faultlessly for 2 years. Here in Australia Victron only sells the 450/200 with MC4 inputs.
V
I tried the search function but didn’t have any luck. A 2 wire connection cable came with the generator with a green connector on one end for the multi and a plug on the other end for the generator. I’ll purchase some number 6awg cable and a plug for the 50 amp connection then wire it to AC-in. I think after that it’s just change the settings and the switch on the Multi?
V
I am planning to setup the inverter and the charger (for refresh battery) in a truck. I wonder if we can combine the charger and the inverter by using the multiplus instead. Since we don’t have the secondary battery, what should be the best way to join the DC output of the multiplus to the car electrical system? If I understand correctly both inverter and charger can connect directly to the car electrical system, but multiplus cannot.
V
Also found the potentiometer explaining.. is for the charge settings..
V
Problem of the no load switch off, found.. On top of the powerunit there is a coil with a fuse.. wire was not making proper contact with the fuseholder.. Crappy automotive stuff / design.. looks like a rapid, we found a problem modification/ solution.. Will make something better solution That was also explaning that with a plus 100 watt load or something inductive like a transformer the inverter did not switch off.
V
Ciao a tutti! Vorrei potenziare la mia barca con un impianto solare che carica le batterie, ad oggi monta 2 batteria al Piombo da 80ah, 1 per il motore e una per i servizi, tra le due batterie c’è un ponte a diodi Ho un caricabatterie da 220v che è collegato alla batteria servizi, quindi non mi carica quella Motore quando sono in banchina Qualcuno mi aiuta su cosa montare per ricaricare 2 batterie con il fotovoltaico che installerò sul capolino della barca? Grazie a tutti Riccardo