XIO

xWire

Posts from every feed QUEST has found across the web — blogs, news, podcasts, channels and more.

Victron Community - Topics tagged vrm

Topics tagged vrm

MPPT seit zwei Wochen offline keine Warnung im VRM

Moin zusammen, ich musste eben feststellen, dass einer meiner beiden MPPT-Laderegler seit rund zwei Wochen nicht mehr funktioniert hat, weil offenbar keine Verbindung mehr zum GX-Gerät bestand. Was mich besonders wundert: Ich habe über das VRM-Portal keinerlei Warnung oder Benachrichtigung erhalten. Früher wurde mir unter „Alarme“ beispielsweise folgende Meldung angezeigt, wenn ein MPPT ausgefallen ist: Solar Charger - MPPT WEST [274] – Error code: #67 - No BMS Kann sich jemand erklären, warum…

Accu percentage in VRM portal ongelijk met echte accu percentage

Hallo, Ik heb een 48/5000 multiplus systeem met JK BMS 32 KW accu’s (LIFE04). Gisteravond heb ik het systeem “houd accu’s geladen” gezet, om de accu’s te laten balanceren. Vanochtend zag ik dat op het dashboard dat de accuwaarde 90 % is. Op het display van de accu’s stond 99 % (dus wellicht ook 100 % gehaald vannacht). Ik heb het systeem weer omgezet naar “geoptimaliseerd zonder batterylife”. Nu is mijn vraag waarom wijkt dit af van elkaar. Het systeem draait nu voor een maand, en hoe kan ik…

Configuring a Multiplus-II: Config Software? Connection?

Hello Everyone, I’ve recently build a offgrid solar system around Victron hardware (BlueSolar MPTTs, SmartShunts, Cerbo GX) including a Multiplus-II 5000/48/70. While I have almost everything configured and working just as I expect it, one thing is not done yet: The Multiplus. My goals are: Set a SOC based shut off limit, that uses a SOC as reported by a SmartShunt. Enable the Multiplus to be turned on / off by the virtual load switch of the MPPT. I was a bit surprised to see, that I cannot…

VRM Quick Navigation & Battery Depletion Overlay

Hi everyone, I wanted to share a browser extension I’ve been developing for the Victron VRM dashboard (VRMplus) It aims to make monitoring and analyzing telemetry a bit smoother with a couple of key tweaks: Quick Navigation & Zoom: Lets you jump around and zoom into dashboard charts faster and more fluidly. Storage Depletion Overlay: Adds a live estimated battery depletion overlay on your dashboard based on a rolling moving average of your real-time power consumption. The project is hosted on…

Feature Request: Include Wind Charger Power in DC System Power Calculation (Venus OS)

Hi Victron Community, I would like to suggest a small improvement to Venus OS regarding the calculation of DC System Power / DC Loads. I have a wind turbine connected to my battery system, monitored by a Victron SmartShunt configured as Wind charger (MonitorMode = -8). Currently, Venus OS does not include the power from this SmartShunt in the estimated DC System Power calculation. This causes the reported DC consumption to be incorrect when the wind turbine is generating power. I managed to fix…

Warmte pomp zichtbaar maken met vm3p75ct

Ik heb mijn hele huis achter de AC-out zitten. Zojuist toegevoegd een vm3p75ct, helaas kan ik die de rol van heat pump dus niet geven zoals er wel op vele plaatsen wordt vermeld. IK kan hem wel als AC belasting laten meten maar dan wordt hij niet apart zichtbaar op het CerboGX scherm of in de vrm portal. Hoe kan ik dit wel voor elkaar krijgen? 15 posts - 4 participants Read full topic

Möchte die neue Remote Console verwenden Zeigt mir Gerät ist nicht im VRM verbunden

ESS bestehend aus 3 Multiplus II 5000 Parallel geschalten 3 Pylontech US 5000 im Moment noch 1 MPT 250/60 Möchte die neue Remote Console verwenden Zeigt er dann die Fehlermeldung “Gerät ist nicht im VRM verbunden” im der Divice List wird alles Richti Angezeigt wo dran kann das liegen. 12 posts - 4 participants Read full topic

Solarsense 750 verliert/ restet Tagesertrag

Hallo in die Runde, beim Solarsense 750 mit der aktuellen Firmware ist mir aufgefallen, dass er öfter den Tagesertrag am Tag verliert, bzw auf null resetet. Wie der Tagesertrag untertägige zurück springt ist auch in VRM gut zusehen . In Victron Connect ist es das gleiche Verhalten Der Solarsense hängt über den Shelly BLE extender am GX Gerät Irgend jemand eine Idee dazu? 13 posts - 3 participants Read full topic

SmartSolar MPPT 250/100 – 52-55V at MPPT PV input at night

Hello, I would particularly appreciate a technical response from Victron regarding the following behavior of my charge controller. I would like to know whether this is normal operation or a fault that should be addressed under warranty. I have four Victron SmartSolar charge controllers installed: 3× MPPT 250/85 – in operation for approximately 1 year 1× MPPT 250/100 – in operation for approximately 6 months All four controllers are running on firmware version 3.18 and are connected via VE.Can.…

Temperature confusion

I am getting confused by the different temperature readings. Since 2 months I have 2 Victron LifePO4 NG 25.6 V 300 Ah batteries on my yacht. I keep a close eye on cell voltage, balance and the temperature. Yesterday I had measurement of 46 degrees showing on the dashboard of VRM and on the Remote Console. That scared me. When I checked the the detailed temperature of the cells, it said it was only 14 degrees. So now I am confused. See screenshots. Where is the measurement of 46 degrees coming…

Spurious low battery warnings

Hi for quite some time now I regularly get low battery ALERTS notifications from VRM while my battery is completely fine with pleny of chenergie. The CLEAR message always follows a few seconds after that. The system is setup with a min charge setting of 11%. See below email I received while the battery is at around 51%. From: VRM Notifier bounces@victronenergy.com Subject: ALERT - ‘Hweg’: ‘Low battery’ on ‘VE.Bus System [276]’ Date: Wed, 4 Nov 2026 18:48:49 +0100 (CET) To: marcel@emol.nl VE.Bus…

VRM release notes 04-11-2026

Hi all, I would love to share with you the latest changes that were just added to production VRM: The Dynamic ESS chart on the dashboard now only loads once you scroll down to it, so the rest of your dashboard opens faster. On mobile devices, the Dynamic ESS chart now shows the time axis in 2-hour steps, just like the EV Charger chart. The labels no longer crowd together, which makes the chart much easier to read on a small screen. The AI assistant no longer jumps to the bottom of the chat…

Suggestion: Improve Alarm and Warning Notifications

Do you think Alarm and Warning Notifications could be improved? Here are a few ideas. better use of color and icons for consistency in VRM and Venus OS GUIv2 sort order of most recent alarms and warnings on GUIv2 Actual values that triggered alarms and warnings (I can’t remember what the thresholds were set to, so I would have to go digging in configuration in the middle of the night, so either tell me the value or give me the threshold and units eg Overload happens when > 1000W or 1200VA). Was…

What are the benefits of using a Victron battery with an external BMS?

I’m designing an electrical system for my small overland vehicle. Currently, I’m considering two options: A cheaper option with a non-Victron battery (built-in BMS). The non-Victron battery has a built-in heater. A more expensive option with a Victron battery and an external BMS. The Victron NG 12.8V, 200Ah battery does not have a built-in heater. Any advice on how to address this would be appreciated. Being able to charge the battery at temperatures below 0°C would be helpful, as I plan to…

My cerbo GX stopped connecting to VRM portal since Sept 22

My cerbo cannot connect to the VRM servers. It shows a connection error> 152 timed out. The cerbo had not made any updates as it cannot connect to vrm so i manually updated the firmware and am now running 3.81. I have tried many things. I am connected through a Starlink connection, i have had this connection for months and there were no changes made on my part when it stopped connecting to vrm. Any help welcome. thanks 9 posts - 3 participants Read full topic

Pylontech US5000 on firmware v1.3: where to get the official file for VRM "Upload firmware file"

Hi all, I’d like to update the BMS firmware of my Pylontech batteries through VRM, and I’m not sure where to get the right file. System Cerbo GX on Venus OS v3.85, MultiPlus-II 48/5000/70-50 (VE.Bus 568), ESS 2× Pylontech US5000 on CAN-bus. Master module (around Aug 2023), BMS firmware v1.3 What I see VRM → Device List → Firmware update shows the battery as Installed v1.3, Latest N/A, with only an “Upload firmware file” button. The GX lists only the master module as updatable. Questions Where…

Im VRM Portal wird die "pv voltage (v)" bei den benutzerdefinierten Widgets nicht angezeigt

Hallo Geräte: SmartSolar 75/15 und GlobalLink 520. Obwohl und gemäss VictronConnect App eine PV Spannung von 54V anliegt wird die “pv voltage (v)” Kurve im VRM Portal nicht angezeigt. Die Kurven der Batterie Spannung und Ladestrom werden einwandfrei angezeigt. Wer weis Rat wie man die “pv voltage (v)” Kurve angezeigt bekommt ? Besten Dank zum Voraus. 5 posts - 2 participants Read full topic

Forecast issues after daylight savings time ended

Hi team, Our DST ended this weekend and I noticed 2 issues with my VRM forecast chart below: The hover-over for any adjusted forecast values show times ending in XX:45 - YY:44. I believe it should be XX:00 - XX:59. Our EV is scheduled to charge at 9pm, and has been for many months now. Last week, VRM would correctly forecast it at 9pm. However the forecast is now showing the EV charge at 8PM. This is suggesting the consumption forecast is now ‘off by one hour’ due to the end of DST. Could…

Disabling OneID

This move to 2FA has been all very well, but this in the only one in dozens of implementations that has let me down and locked me out. Thankfully the login via link works, but I want to disable this now. I’d rather wait till proper passkey support is there, I am sick of maintaining 100 different MFA tokens. However, I don’t see any way to actually remove or disable the now broken 2FA that was setup. 3 posts - 2 participants Read full topic

Local login to Cerbo

Hello all, I cannot log-in on local network to my new version (Mk3) Cerbo GX as the password (which I have not set) is not recognised. I have tried all of the standard default password variations with no luck. I can access via VRM remotely with no problem, any ideas? I have not ever had this problem with earlier Cerbo’s 22 posts - 6 participants Read full topic

3-phase Multi RS 48/6000: one unit loses the others, AC-out drops, grid stays up

Hi all, My three-phase system occasionally drops the AC output for a few seconds while the grid itself stays up. As far as I can tell, one Multi RS loses contact with the other two, all three shut down and then restart. My NAS on AC-out logs the outages, but VRM shows almost nothing. System 3× Multi RS Smart 48/6000/100, three-phase, firmware v1.31 (all three) Cerbo GX MK2, Venus OS v3.80 (Large); the outages below happened on v3.79 64 kWh LiFePO4 battery with CAN-bus BMS (shown as “Generic…

Ekrano Update V3.80 auf V3.85

Moin liebe Community! Habe meinen Ekrano letzte Woche von Version 3.80 auf 3.85 geupdatet. Dabei ist mir aufgefallen das meine PV Anlagen nur noch an der Position vom AC1 IN angezeigt werden. Normal sollte eine am AC out angezeigt werden. In der App und im VRM ist alles auch so nur am Ekrano selber nicht. Hat jemand eine Idee oder das selbe Problem? Gruß in die Runde 7 posts - 3 participants Read full topic

VRM app: how to turn off AI icon?

Hi there, First, I have been using the VRM for a while now & it is absolutely grand, it’s been a gamechanger for our offgrid setup. Thankyou However, similarly to this topic here Introducing the VRM AI Assistant I need to be able to turn this off. the big difference since this topic is: there is now one of these on the front dashboard & it (and its friend in the Advanced view) are animated. I’m neurodivergent & I cannot concentrate with these things wriggling about in the corner like a child…

Does the VM-3P75CT & VM-3P5A log VA and PF in VRM

Does the VM-3P75CT & VM-3P5A log VA and PF in VRM as time-series data? I’m working with a customer that runs a summer camp off-grid on three phase diesel generators. They have no energy meters with logging and they can’t tell me what their peak and average loads and daily energy needs are since they don’t log the data. The camp uses three phase commercial equipment in the kitchen (i.e. mixers, refrigeration) and three phase septic lift pumps and well water pumps so I want to log VA and PF along…

Victron DESS alternatief

Heb zelf maar een Victron DESS alternatief gebouwd (fork van Optivolt van bmesuere). Draai nu al aantal dagen op laatste versie en werkt voor mij prima en heb wat Victron DESS eigenaardigheden weten op te lossen. Foto 1 is resultaat laad en ontlaad gedrag Victron DESS, foto 2 van mijn geoptimaliseerde DESS. Voordeel is ook dat het veelal lokaal kan draaien (onafhankelijk van Victron cloud) en geen black box is. Samen met geoptimaliseerde Epexpredictor fork (specifiek NL voorspellers toegevoegd)…

MPPT Smart Solar keine Reaktion

Hallo in die Runde, Ich stehe heute mit einer Frage betreffend eines Solar Ladereglers vor Euch folgendes System, ich betreibe 3 Stk. Solarpanele 100W/18V/5,56A in Serie über einen Trennschalter an einem Smartsolar MPPT 100/30 am Abgang mit 16mm2 und SI 40A an die Plusbusschiene weiter zur Batterie. Das selbe System ein zweites Mal auch an die Plusbusschiene, an der plusbusschiene hängt auch noch über Sicherungen ein Victron IP43 smart ladegerät sowie ein Victron Ladebooster, dieses System hat…

Vrm remote konsole aufruf scheitert

Ich finde den Beitrag zum VRM-Update nicht mehr, in dem es um die Probleme beim Aufruf der Remote Konsole aus der Web-VRM-Version ging. Mir fällt es in den letzten Tagen vermehrt wieder auf, dass ich die VRM Seite nach Tabwechsel oder Standby aktualisieren muss bevor ich die Remote Konsole aufrufen kann. Ausserdem haben trotz aktivem Echtzeitstatus die Opportunity Loads Schalter gelegentlich den falschen Status oder werden nicht alle angezeigt. 6 posts - 4 participants Read full topic